[Jun 26, 2026] CSSBB Exam Dumps PDF Guaranteed Success with Accurate & Updated Questions [Q133-Q157]

[Jun 26, 2026] CSSBB Exam Dumps PDF Guaranteed Success with Accurate & Updated Questions

Pass CSSBB Exam - Real Test Engine PDF with 287 Questions

Certification Path

If you're striving for perfection and want to further polish your skills in the area of Six Sigma, then you can sustain your education by opting for the ASQ Master Black Belt (MBB) certification, which is a natural step to take after the CSSBB.

NEW QUESTION # 133
A stable, normally distributed process with specification 3.50 .03 has = 3.51 and = .016. What percent of the production violates specification?

A. 16.43%
B. 18.58%
C. 11.18%
D. 12.62%

Answer: C

NEW QUESTION # 134
Which of the following actions is an example of a kaizen project?

A. Designing a next-generation product
B. Redefining product specifications
C. Partnering with suppliers to improve quality issues
D. Relocating a manufacturing facility overseas

Answer: C

Explanation:
The correct answer is C. Partnering with suppliers to improve quality issues . The CSSBB source defines kaizen as continuous, incremental improvement involving everyone, with emphasis on improving processes , maintaining and improving standards, using PDCA/PDSA cycles, and solving problems with data.
The supporting Lean Six Sigma material also describes kaizen as small incremental improvements that add up over time rather than large, radical change.
Among the choices, partnering with suppliers to improve quality issues is the one that best reflects a practical, process-focused, continuous-improvement effort. It is targeted, collaborative, and aimed at improving ongoing performance rather than creating a wholly new design or making a major strategic relocation.
Redefining product specifications and designing a next-generation product are more aligned with design or innovation activities, while relocating a facility overseas is a major strategic business change, not kaizen.
Since kaizen focuses on improving existing processes and quality through incremental action, partnering with suppliers to improve quality issues is the best example. Therefore, the verified answer is C .

NEW QUESTION # 135
Find Cp

A. 1.33
B. 0.44
C. 2.00
D. 0.56

Answer: D

NEW QUESTION # 136
Statistical Difference is the magnitude of difference or change required to distinguish between a true difference, brought about by change or improvement, and one that could have occurred by chance.

A. False
B. True

Answer: B

NEW QUESTION # 137
The most appropriate type of FMEA for a product before going into manufacturing is a ___________ FMEA.

A. Design
B. Test Process
C. Consumer
D. Survey

Answer: A

Explanation:
Explanation

NEW QUESTION # 138
A meeting is called for all three shifts to determine the settings to be used on machine #45. This is an example of:

A. standard work
B. poka-yoke
C. kanban
D. set up time reduction (SMED)
E. visual factory

Answer: A

NEW QUESTION # 139
Following process modifications, the Null Hypothesis states that no improvement to the process has occurred. If we discover the Null Hypothesis Test was rejected when it was false that would be a(n) _______________.

A. Alpha Error
B. Type III Error
C. Type I Error
D. Type II Error

Answer: D

NEW QUESTION # 140
When comparing two vendors' machines it is found that a sample of 1000 parts from machine A has 23 defectives and a sample of 1300 parts from machine B has 36 defectives. Do the data indicate that machine B has a higher rate of defectives?

A. yes
B. no
C. all of the above

Answer: A

NEW QUESTION # 141
Early in a project a Belt will want to begin to identify and evaluate risk factors for the subject process and will therefore begin building a(n) ________.

A. X-Y Diagram
B. FMEA
C. Team Charter
D. SIPOC

Answer: B

NEW QUESTION # 142
Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. The statistical Degrees of Freedom for this example are?

A. 0
B. 1
C. 2
D. 3
E. 4

Answer: C

Explanation:
Explanation

NEW QUESTION # 143
Which statement(s) are correct about the Factorial Plot shown here? (Note: There are 3 correct answers).

A. The coefficient of the metal hardness is positively related to the output of tool age
B. These plots prove a statistically significance factor with 95% confidence
C. These plots are an example of interaction plots
D. The coded coefficient is lower for cutting speed than the cutting angle related to the output of tool age
E. When the cutting speed increased from low to high level, the tool age increases

Answer: A,D,E

NEW QUESTION # 144
Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. For the sales accomplished above, what test would validate if they met their requirements?

A. Test for Equal Variance
B. F Test
C. Chi Square Test
D. One-Sample t-Test

Answer: D

NEW QUESTION # 145
Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o
F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. The statistical Degrees of Freedom for this example are?

A. 0
B. 1
C. 2
D. 3
E. 4

Answer: C

NEW QUESTION # 146
What conclusion is most correct about the Experimental Design shown here with the response in the far right column?

A. If the Adv is increased from the low level to the high level, the response rate increases
B. This design does not have enough experimental runs to conclude anything as evidenced by the lack of P- values in the MINITABTM output
C. Constant, Adv and Bev are the only factors statistically affecting the response rate with 95% confidence or more
D. The response level is statistically concluded to only need the Adv and Bev factors set at the low level to get the largest response rate
E. No factor has enough statistical confidence greater than 95% to have an impact on the response rate

Answer: D

NEW QUESTION # 147
In a process improvement project, a Six Sigma Black Belt measures discrete data including error counts in the final product. This discrete data can also be referred to as

A. stratified data
B. attribute data
C. a data collection plan
D. continuous data

Answer: B

Explanation:
The correct answer is A. attribute data . In the CSSBB source, attribute charts are used for characteristics such as pass/fail, good/bad, number of defects, and number of defectives, and the text explicitly states that attributes are discrete, counted data . This fits the question exactly because error counts in the final product are count-based and therefore discrete rather than continuous. The CSSBB material also identifies attribute data as one of the primary types of data used in Six Sigma, alongside variables data and locational data.
A data collection plan is a method for organizing how data will be gathered, not a type of data. Stratified data refers to data separated into meaningful subgroups, such as by shift, machine, or supplier, but that does not define whether the data are discrete or continuous. Continuous data, by contrast, involve measurements on a scale such as weight, time, or length. Since the question specifically describes discrete counts of errors, the CSSBB-consistent term is attribute data . This is why the best and verified answer is A .

NEW QUESTION # 148
According to the Central Limit Theorem:

A. the median and the mean have the same value in a symmetric distribution
B. none of the above
C. the mean of an exponential distribution is smaller than the median
D. the mean, median and mode of a normal distribution all have the same value
E. the mode of a normal distribution is also the mean

Answer: B

NEW QUESTION # 149
This QFD matrix was used in the design process for a ball point pen. What symbol is appropriate for the square labeled 6?

A.
B.
C.
D. none of the above
E.

Answer: B

NEW QUESTION # 150
"Robust design" refers to the ability of the product or service:

A. to have a high reliability
B. to function the same in different conditions
C. to last a long time
D. to remain strong

Answer: B

NEW QUESTION # 151
The number of factors, levels and replications:

A. 3, 2, 3
B. 3, 3, 3
C. 2, 3, 2
D. 2, 2, 2
E. 3, 2, 2,
F. none of the above

Answer: A

NEW QUESTION # 152
Which of these graphs demonstrates conditions which would be sufficient to enable OCAP for the process?

A. Xbar Chart
B. Time Series Chart
C. Both
D. Neither

Answer: A

NEW QUESTION # 153
To properly analyze the variables impacting the output of a process we need to collect data that represents at least 80% of the variation in the process and assure ourselves we are collecting data from all three types of variation which are _______________.

A. Induced, Natural and Unavoidable
B. Within, Between and Temporary
C. Without, Above and Below
D. Within, Between and Temporal

Answer: D

NEW QUESTION # 154
A dock worker for a feed supplier was tasked with assuring the proper weight in the feed bags as they left the dock. One of the columns listed the range of weight of the bags included in the studies. This required plotting a Histogram of the weight of the bags. While drawing the Histogram the x-axis contained a certain scale of data. Pick the scale of data that is appropriate for Histograms.