Cisco 350-501 Certification All-in-One Exam Guide Oct-2023
Get Real 350-501 Exam Dumps [Oct-2023] Practice Tests
NEW QUESTION # 14
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
- A. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- B. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- C. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
- D. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
Answer: B
NEW QUESTION # 15
Refer to the exhibit:
Which configuration prevents the OSPF neighbor from establishing?
- A. mtu
- B. network statement
- C. duplex
- D. default-metric
Answer: A
NEW QUESTION # 16
Refer To the exhibit:
On R1, which output does the show isis neighbors command generate?
A)
B)
C)
D)
- A. Option B
- B. Option A
- C. Option D
- D. Option C
Answer: C
NEW QUESTION # 17 
Refer to the exhibit. If router RA is configured as shown, which IPv4 multicast address space does it use?
- A. 232.0.0.0/8
- B. 224.0.0.0/8
- C. 225.0.0.0/8
- D. 239.0.0.0/8
Answer: A
Explanation:
Section: Services
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/multicast/ configuration_guide/b_mc_3se_3850_cg/b_mc_3se_3850_cg_chapter_01011.html
NEW QUESTION # 18
Refer to the exhibit:
This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A. It shows the hostname of the device as rpc-reply
- B. It shows NETCONF uses remote procedure calls.
- C. It shows that the full configuration is being modeled by VANG
- D. It shows that the running configuration is blank
Answer: A
NEW QUESTION # 19
Refer To the exhibit:
On R1, which output does the show isis neighbors command generate?
A)
B)
C)
D)
- A. Option B
- B. Option A
- C. Option D
- D. Option C
Answer: C
NEW QUESTION # 20
Refer to the exhibit.
What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?
- A. OSPF process IDs match
- B. authentication is added to the configuration
- C. correct wildcard mask is used on Router 2
- D. hello intervals match
Answer: D
NEW QUESTION # 21
Refer to the exhibit. An engineer is configuring an administrative domain in the given multi-vendor environment with PIM-SM.
Which feature must the engineer implement so that devices will dynamically learn the RP?
- A. Auto-RP
- B. BSR
- C. BIDIR-PIM
- D. SSM
Answer: B
NEW QUESTION # 22
Refer to the exhibit:
Which statement about this configuration is true"?
- A. It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run
- B. It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels
- C. It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing
- D. It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run
Answer: D
NEW QUESTION # 23
How does Inter-AS Option-A function when two PE routers in different autonomous systems are directly connected?
- A. The two routers treat one another as CE routers and advertise unlabeled IPv4 routes through an EBGP session.
- B. The two routers share all Inter-AS VPNv4 routes and redistribute routes within an IBGP session to provide end-to-end reach.
- C. The two routers establish an MP-EBGP session to share their customers' respective VPNv4 routes.
- D. The two routers share VPNv4 routes over a multihop EBGP session and set up an Inter-AS tunnel using one another's label.
Answer: A
NEW QUESTION # 24
Refer to the exhibit:
When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.
Which factor should be the reason for this situation?
- A. LDP needs to be enabled on the R2 physical interface
- B. LDP needs to be enabled on the R2 loopback interface
- C. R2 does not see any hellos from R1
- D. R2 sees the wrong type of hellos from R1
Answer: C
NEW QUESTION # 25
Refer to the exhibit. Routers P4 and P5 receive the 0.0.0.0/0 route from the ISP via eBGP peering. P4 is the primary Internet gateway router, and P5 is its backup. P5 is already advertising a default route into the OSPF domain. Which configuration must be applied to P4 so that it advertises a default route into OSPF and becomes the primary Internet gateway for the network?
- A. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 2
end - B. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 1
end - C. configure terminal
router ospfv3 100
address-family ipv4 unicast
redistribute bgp 65500 metric 40 metric-type 1
end - D. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate always metric 40 metric-type 1
end
Answer: A
NEW QUESTION # 26
How can a network administrator secure rest APIs?
- A. They can authenticate user sessions and provide the appropriate privilege level
- B. They can ensure that user sessions are authenticated using TACACS+ only
- C. They can allow read and write privileges to all users
- D. They can have a general administrator login for multiple users to access that has command entries logged
Answer: A
NEW QUESTION # 27
When Cisco lOS XE REST API uses HTTP request methods what is the purpose of a PUT request?
- A. submits data to be processed to the specified resource
- B. retrieves the specified resource or representation
- C. updates the specified resource with new information
- D. creates a new resource
Answer: C
Explanation:
NEW QUESTION # 28
Which statement about segment routing prefix segments is true?
- A. It is the longest path to a node
- B. It is linked to a prefix SID that is globally unique within segment routing domain
- C. It is linked to an adjacency SID that is globally unique within the router
- D. It requires using EIGRP to operate
Answer: C
NEW QUESTION # 29
An engineer is implementing MPLS to monitor within the MPLS domain.
Which must the engineer perform to prevent packets from being forwarded beyond the service provider domain when the LSP is down?
- A. Disable IP redirects only on outbound interfaces.
- B. Implement the destination address for the LSP echo request packet in the 127.x.y.z/8 network.
- C. Configure a private IP address as the destination address of the headend router of Cisco MPLS TE.
- D. Disable IP redirects on all ingress interfaces.
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r7-
5/mpls/configuration/guide/b-mpls-cg-asr9000-75x/implementing-mpls-oam-74x.html
NEW QUESTION # 30
Which statement about segment routing prefix segments is true?
- A. It is linked to an adjacency SID that is globally unique within the router.
- B. It requires using EIGRP to operate.
- C. It is the longest path to a node.
- D. It is linked to a prefix SID that is globally unique within segment routing domain.
Answer: D
Explanation:
Section: MPLS and Segment Routing
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/segment-routing/configuration/ guide/b-seg-routing-cg-asr9k/b-seg-routing-cg-asr9k_chapter_010.pdf
NEW QUESTION # 31
Refer to the exhibit. R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed.
When the debug ip ospf hello command is issued on R1, these log messages are seen.
Which command can be configured on routers R1 and R2 on f0/0 interfaces to form OSPF adjacency?
- A. ip ospf network point-to-point
- B. ip ospf network point-to- multipoint non-broadcast
- C. ip ospf network broadcast
- D. ip ospf network non-broadcast
Answer: A
Explanation:
https://community.cisco.com/t5/routing/ospf-point-to-point-links/td-p/1913398
NEW QUESTION # 32
Refer to the exhibit:
With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?
- A. 192.168.0.3
- B. 192.168.0.5
- C. 192.168.0.1
- D. 192.168.0.4
Answer: A
NEW QUESTION # 33
Refer to the exhibit. To protect in-band management access to CPE-R7, an engineer wants to allow only SSH management and provisioning traffic from management network 192.168.0.0/16.
Which infrastructure ACL change must be applied to router PE-R9 to complete this task?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 34
Refer to the exhibit:
Export statistics received do not include the BGP next hop.
Which statement about the NetFlow export statistics is true?
- A. To include the BGP next hop in the export statistics, those keywords must be included with the version
9 entry. - B. Loopback 0 must be participating in BGP for it to be included in the export statistics.
- C. The origin AS and the peer-as will be included in the export statistics.
- D. Only the origin AS of the source router will be included in the export statistics.
Answer: A
NEW QUESTION # 35
The administrator of a small company network notices that intermittent network issues occasionally cause inbound notifications to its SNMP servers to be lost. Which configuration must the administrator apply so that the SNMP servers acknowledge the notifications that they receive?
- A. snmp-server community ciscotest rw 10
- B. snmp-server enable traps bgp
snmp-server host 192.169.2.1 Informs - C. snmp-server enable traps snmp
- D. snmp-server host tests.cisco.com public
snmp-server community ciscotest rw 10
Answer: B
NEW QUESTION # 36
Which Cisco software OS uses monolithic architecture?
- A. IOS XE
- B. IOS XR
- C. NX-OS
- D. IOS
Answer: D
Explanation:
Cisco Internetwork Operating System (IOS) is the software used on most Cisco Systems routers and current Cisco network switches. IOS is a package of routing, switching, internetworking and telecommunications functions integrated into a multitasking operating system. IOS uses a monolithic architecture, meaning that all processes run in a single address space, making it a single-image system.
NEW QUESTION # 37
An network engineer is deploying VRF on ASBR router R1. The interface must have connectivity over an MPLS VPN inter-AS Option AB network. Which configuration must the engineer apply on the router to accomplish this task?
A)
B)
C)
D)
- A. Option B
- B. Option A
- C. Option D
- D. Option C
Answer: C
NEW QUESTION # 38
......
Last 350-501 practice test reviews: Practice Test Cisco dumps: https://torrentvce.certkingdompdf.com/350-501-latest-certkingdom-dumps.html